adcom gfa555 or carver tfm35
hi everyone looking at these to amp for a 2 channel music set up adcom gfa555 or carver tfm35,any opinions would be helpful thanks
View ArticleExpert Opinions Please!
Greetings and Salutations form the metropolis of Wentzville, Missouri! I am in need on expert advice regarding the purchase of a new surround sound system for my man cave. Originally, I was going to go...
View ArticleClik here to view.
Computer speakers Thought experiment help
So here I am getting tired of my current computer speakers. Which BTW are some cheap shielded Sony woofers in a tin can filled with BAF. Using the drivers I have on hand I am thinking of a small 3-Way...
View ArticleYahama m60 amp
looking for a part sub for D117 listed on manual as HZ-6CIL is this a 6volt ziener or does anyone know where i can get a sub for this thanks in advance Tom:eek:
View ArticleFYI Hafler amp,pre, and tuner
saw this in Craigslist Orlando HAFLER HOME AUDIO hope somebody gets it Regards , E
View Articlecrate_technical_support_abandonment
1. please assist technical resolve SE tube amp drooped voltage condition. 2. vc508 older model, alterated as follows: 3. replaced ht rectifier to 3 ampere fast diodes type 4. added htdc snubber .1uf 5....
View Articleelectronic bikes
Wonder if we might discuss 'e-bikes' Perhaps: 1 - modding the controller 2 - battery replacement 3 - charger replacement 4 - accessories 5 - brands I have an e-bike - live in China - have some...
View ArticleClik here to view.
targa 200 amp led turns on and off under a load
this is an old targa hexfet 2ch 200 watts amp.when rca.s installed and speaker wires hooked up it is fine. when it is turned up , the power led turns off and on. the output transistors and power supply...
View ArticleClik here to view.
Making an electrostatic headphone driver.
Dear all, I am currently building a driver for a Stax Lambda Pro before I start work on my own electrostatic headphone. the first version will be built to low cost, a later version may be more Super...
View ArticleClik here to view.
Loop stability clarification . . .
Hey guys, I've got a couple Bode plots for you to look at. I'm a bit puzzled by this and hope you can help me sort things out. First, open loop. Then, closed. In simulations, the closed loop is stable,...
View ArticleCrossover components in Ottawa?
Right now I am looking at $45 for $25 in parts from Solen. Wondering if I can save $15 by buying local in shipping. Any ideas? Thanks fellow Canucks.
View ArticleStereo to Mono
I have a powered speaker (Behringer B215D). What is the best way to plug an iPod into ONE SPEAKER? Here is the I/O diagram: http://www.behringer.com/assets/B208...5D_fig1_XL.png Is there anyway to...
View ArticleStereo To Mono with SINGLE Powered Speaker
I have a powered speaker (Behringer B215D). What is the best way to plug an iPod into ONE SPEAKER? Here is the I/O diagram: http://www.behringer.com/assets/B208...5D_fig1_XL.png Is there anyway to...
View ArticleHelp Adding A 3.5mm Jack To Factory Stereo
Hey, I am about to attempt a project to add a 3.5mm jack to my 2002 Pontiac Bonneville's factory radio, so I can connect my iPod to it without having to buy an aftermarket radio. Also, I know there are...
View ArticleClik here to view.
help me understand this enclosure
So I am hacking an old 2.1 pc system for the amp and sub (altec lansing 621, screen shot of specs below) and using the dayton audio rs100-4 as the satellites. I am enclosing all of the components into...
View ArticleCAS-1 Repair
Hi Folks, I'm new here and looking for advice on replacing the bridge rectifiers on my CAS-1. I've read on here about some newer types but haven't found any current or voltage values so I know what to...
View ArticleNew enclosures for DIY
We manufacture custom sized aluminum enclosures for DIY projects. We can currently make enclosures 2.25, 3.25 and 4.25 inches tall. The width and depth are configurable in 1/32 inch increments between...
View ArticleWTB Tang Band W4-1320SIF
Looking to buy a pair of Tang Band W4-1320SIF if anybody has some. Thanks.
View ArticleClik here to view.
Aikido 9-pin All-in-one Testing question
I'm about to plug my newly constructed Aikido in and I'd like to run thru the test procedure John has specified in his instructions. I've got the heater supply tranny wired in and the high voltage...
View ArticleClik here to view.
Potato 74G14 vs Fairchild 74VHC14
Hi, Does anyone know about how to optimise a circuit for the faster Potato ? I recently swapped a 74VHC14 for the Potato 74G14 and the sound is substantially worse. It is used to distribute the output...
View Article