PS Audio I2S interface
I'm trying to connect a PS Audio Perfect Wave Transport to an Audio GD Master 7 via I2S. Does anyone have the pinouts for the PS Audio I2S HDMI connector and the Master 7 I2S RJ45 connector Thanks Marc
View ArticleMicrolab Solo6c Mods
Hi everyone so I decided to mod my solo6c I ripped the old amp and transformer out to make them a passive pair then ive lined just the back,top.bottom with acoustic damping material this took a while...
View ArticleClik here to view.
FS: Avel Y23604 160VA 2x25V
I have a pair of Avel Y236504 toroids for sale. These have been used in Aspen Aksa and Lifeforce amplifiers. $50 for the pair. Attached Images Avel Y236504_2.jpg (502.4 KB)
View ArticleClik here to view.
FS: Triad Magnetics 160VA 2x24V Toroids
I have a pair of Triad Magnetics toroids, 160VA 2x24V. These were used in a Fetzilla amplifier for a short time. $60 for the pair. See link below: VPT48-3300 - TRIAD MAGNETICS - TOROIDAL POWER...
View ArticleSustainability in Audio ...
Hi All, I've been visiting these forums for quite some time now and have noticed how active and creative diy'ers here are. It's really inspiring ;) However, in searching around here, I have never seen...
View ArticleClik here to view.
FS: 8th note relay Stepped Attenuator
For sale is the last single ended stepped attenuator. Product info is at: 8th note - Stepped attenuator details page It is suitable for stereo projects. The attenuator is assembled and tested. Remote...
View Articlefriends outdoor project
I know I have some educating to do, as his request is for an outdoor sub for movie special effects that won't bother the neighbors in a small portable box. That part I can deal with. I have not been...
View ArticleMedia Player HELP!
I've not had a lot to do with media streaming before, but I would like to buy a couple of really big drives to centralize my media, and stream various sources from a player using the local area network...
View Article5.5 inch midrange driver or 2 inch dome midrange?
I would like to build a 3 way system but as observed almost all the cone drivers has breakup after 2khz no matter its nomex or reed or kevlar or even magnesium. I have seen dome midrange from 800hz to...
View ArticleSolid state speaker protection system - interest check
Hello all! I think most of us are running loudspeaker DC protection in our DIY amplifiers; even if they can be considered highly reliable such protection also alleviates power on/off thump. I'm also...
View Article6sn7 pse amp for altec lansing 604E
Hi would a 6sn7 pse amp be possible by tying the anodes for both halves together with the load being a hammond 125ase wired for 10k ohms with an 8 ohms speaker. However due to the speakers I am using...
View ArticleClik here to view.
Sony 7065 PS Rebuild
Hi All, I am rebuilding a Powers Supply for a Vintage Sony 7065 receiver . I have a few metal resistors on the board that are in need of replacement. Can anyone please give me a suggestion for a...
View ArticleM3900 Multimeter Malfunction, can it be fixed?
Hi all, A digital multi-meter (model - M3900, made by Mastech, bought last year ) is behaving in a strange manner. The display is not instantaneous like my other cheap one. It's showing a slow and...
View ArticleClik here to view.
FS: DCB1 (Mezmerize) built with quality parts
Hi all, I've have my old mezmerize to sell. Perfectly working conditions, high quality parts used (Nichicon KW and KZ, PRP, Takman and KOA resistors, genuine Alps pot) Since originally volume pot was...
View ArticleIntroduction and survey for gear junkies!
Hello All, I am a novice guitar player and aspiring gear junkie! I am interested in reading up on all the tube goodness I can, and am sure I will learn a lot on this Forum. I have spoken with several...
View ArticleClik here to view.
Fun selector LED layout..
OK this is for fun.. How do you wire a rotary selector switch using a bridge rectifier and a single diode so that 5 leds light to show the position of the switch ie one led shows position 1, two leds...
View ArticleAltec playback 360 power trans
I scored this power transformer at a yard sale in a lot of tube outputs. It is not for tubes and therefore not needed in my lab. It is a peerless transformer, potted, and when voltage was applied to...
View ArticleThiele and Small Parameters
Anyone out there have the Thiele-Small parameters for the 10" woofer in the Mirage M-3? :o
View ArticleHeathkit AA2004 or AA2010
Hello, do any of you guys (or girls) have a old Heathkit AA2004 or AA2010 sitting around unused that you would like to part with? It doesnt have to be operating so long as it is in decent cosmetic...
View Article