Clik here to view.
Seas H1451-06 27TDNC/GW Tweeter
I have seven of these drivers, which are completely new. I would like to get 140€ excluding shipping per pair of them. They are comparable to Seas H1462-06 27TDFNC/GW. The have better resolution as...
View ArticleClik here to view.
Seas ER18RNX Midwoofer
I would like to sell a pair of these completely new drivers. They are customconfigurated. The use the magnetsystem of the much superior Excelseries. The have 4 Ohms instead of 8 Ohms and a...
View ArticleClik here to view.
Vifa XT 300 KS/4 Tweeter Special Version
I sell this pair of Vifa XT 300 KS/4 tweeters. They are completely new. It's a special version of the well-known Vifa ring radiator with neodymiummagnets and metal-shielding. I would like to get 90€...
View ArticleNeed suggestions to power my portable speaker!
Just got done an install, and I am left with a single JBL control 23. I want to use a T-amp and a li-ion battery to power it, so that I can have a mobile speaker with me for various activities. Any...
View ArticleNutshell Raven Headphone amp with balanced I/O
Hi Guru's I have recently finnished building a headphone amplifier very similar to the Nutshell Raven but the PSU is diode bridge rectified with transistor regulation. I am running the amp fully...
View Article2 way crossover
Hi, IÂ’m trying to design a 2 way crossover using the Dayton Audio RS100-4 4" Reference and Dayton Audio ND16FA-6 5/8" Neodymium Dome Tweeter. What frequency should I cross them at and how would you...
View Articleoption for toroids?
what are good toroids to use for making transformers? i normally reuse them but i have some amps that dont have them.
View ArticleClik here to view.
Zapco early Z and studio series turn-on pop?
Mike from Zapco said, "The turnon pop is normal with these models. It is inherit to the unmuting circuit in the early Z and studio series. There is no fix to this except radical changes to the output...
View ArticleHello from Wisconsin!
Hi everyone! So, a little background first. I've lived in Wisconsin my whole life (18 years). I've been interested in electronics and cars for as long as I can remember and I just recently got into...
View ArticleMan-a-stration
I know the guy is in pain, and it's not funny. Medical boards in many states don't allow gynecologists to treat men: http://www.nytimes.com/2013/12/11/us...oard.html?_r=0
View ArticleSpectra 1100 Screeching
Can anyone kindly help me with my problem, which is that one of my Spectra 1100's has developed a nasty screetchy, distortion with certain material, most noticeable on female vocals played at loud...
View ArticleClik here to view.
3 x Philips AD 12202/M8 Speaker
From disassembling an older analog organ I have left over... 3 x Philips AD 12202/M8 speaker. I would say in mint condition. They sound and look great, there was only a little bit of dust to take of...
View ArticleWanted: Mission Tweeter.
Looking for one of these tweeters folks. Mission Freedom 770. This one: DSC04967.jpg Photo by alexbowie | Photobucket
View ArticleST70 chassis polishing
Greetings! I'm in the middle of a ST70 upgrade/rebuild and am at the point of polishing the chassis. What would be a safe and effective product to use on the chassis that would not damage the lettering...
View ArticleClik here to view.
Question about speaker protection kit circuit
Hi guys, I recently purchased a speaker protection kit from ebay and of course it doesn't come with any literature so I have a question. These are the features is has; The board include the regulator...
View ArticleWanted , Pair of Magnavox 15" from Console
The ones I'm after have smooth cone with bigger alnico magnet . However , I will consider later ones with ribbed cone and small alnico magnet too. let me know what you've got .Thanks , L
View ArticleFlat ribbon cable
There are flat ribbon type cables in a receiver I am working on. It was broken. There is plenty of length to strip and redo it. I am just guessing how to go about it. There are 34 flat aluminum...
View ArticleClik here to view.
stacked mdf speaker box
I want to build something like this. im a machinest and have access to a cnc mill. I have a pair of GRS 8FR-8 from PE on hand id like to use. I wanted to make something along the lines of a folded...
View ArticleClik here to view.
Fosgate Power T600-2
this amp initially blew my test fuse instantly at power up. Opened It and found left channel outputs shorted. Now that they are removed, the T600-2 powers up fine with with a normal blue status light....
View ArticleClik here to view.
FS: Get-Set-Go Single Ended Triode Amplifier
I'm selling this amplifier for a close friend. I took the photos of the amp. Here are the details.... Stereo Tube Amplifier Get*Set*Go Single-End Triode This is a single-ended triode amp built using...
View Article